This is start scripts i am doing cura,s3d,superslicer,prusaslicer but i will add anything anyone asks for i just may need them test it once for me to make sure i get the variable right . this will speed heating a lot as it will do things in tandem instead of waiting plus includes purge line to to make sure it clear and retract at end to make sure no clogs or ooze .
This is way stronger than the stock plate and has spacers built in works with all stock hardware
V6 dragon shroud is the hotend cooler it works with stock as well but works great for the dragon . Body 3 and 4 are very high resolution must be printed with .4 nozzle and line width or will have errors in most slicers. Body 10 is a diff file same setup just mirror for other side
this is a beta version of the newest dwc for the 3.2 rrf it is awesome it works with my posted update for rrf3 which i have tweaked the install guide a little to make it very easy and bullet proof. You should be able to simply dload the duet 2and3 zip file and click install thats it . Then dload this beta by uploading in the system tab as well. The web control may work with 2x to i am going to downgrade and report back to let everyone know for people intimidated by the rrf3 upgrade
Should work with rrf2 as well
This is a prusa based fan cooler set for the dragon nozzle height .
This also allows the removal of the factory red housing to reduce weight .
**** make sure to set min layer time to at least 10 seconds and to block supports from the duct tips but to have supports on the arm where it hangs past base.
1. First upload the .g files for your printer but delete the 300 or 400 off the back and do not restart.
2. Then upload DuetWebControl-SD-2.1.6.zip while inside the System tab, also upload the following bin files from the sys directory, one at a time, in order. Don’t install and restart when prompted for these but upload all then go back and upload again clicking install the second time around . Duet2CombinedIAP.bin, DuetWiFiServer-1.23.bin, Duet2CombinedFirmware_3.0.0.bin . Should be good but if any problems go to console on printer and enter m997 s0:1
Notes
Baud rate must be set to 57600 on the panel please do before starting but if you forget and it isn’t connecting you can change after. I updated instructions to just manually install from printer screen encase files get installed in wrong order this adds few steps but makes It less likely to lose wifi saved settings during upgrade.
*****These configs are for dd extruder if you want to use stock you need to change back to 1200 mah for the extruder driver and also stock timings which are B2 Y4:4 F4 and you do not need to use the bed.g files I just like the double tram I set up. Also make sure to adjust to your probe offset unless you have it saved in your config override. You also will need to revert to original steps which should be around 413 iirc.
******anyone wanting help just send me a zip with their sdcard minus the gcode folder and i will setup everything so that you can just upload the files i send back and not have to worry about anything or can manually take sd card out and copy the files back ont o sd card put back in printer and run a macro from screen i setup for you.
[octoprint_compat]
needs to be added after the newest update is installed so if you click update you need to add this to fix the slicer upload function. add this to the bottom of your moonraker.conf file. Mr Lasenko helped me greatly with getting the website setup so i have shipping and store setup just waiting for my direct acounts with the shipping companies to activate but i will be loading some stuff and also we are making a forum and i am making logins for my patreons so you guys wil have first access to stuff and also diff pricing for stuff “i am planning to markup my upgrades for non patreons and do my stuff at cost for you guys.
www.advanced3dprinting.com is the url
Unlock with Patreon
